High Torque Timing Pulleys P2M/P3M Type

Brand :

MISUMI

Caution

Please note that the swaged flange options, NFC, RFC, and LFC, are not reflected in the CAD data.
Please check the content on our website as the PDF does not contain the most up-to-date information.

Product Description

[Material]
· Pulley: High strength aluminum alloy, S45C equivalent, SUS304
· Flange: Aluminum alloy, SPCC

[ ! ]

■P2M

● Pulley Shape

Shape K

Shape A

Shape B

Standard Tooth Profile

Tooth groove dimensions slightly vary according to the number of teeth. (Pitch: 2.0 mm)

■Belt Nominal Width / Dimensions

mm	Nominal
mm	P2M040	P2M060	P2M100
A	6.0	7.5	12.0
W	10.0	11.5	16.0
L	17.0	20.0	23.0

■Tapped Hole Dimensions

d_H7 Shaft Bore I.D.	M (Coarse)	Accessory Set Screws
3 to 6.35	M3	M3 × 3
7 to 22	M4	M4 × 3

[ ! ] Tapped holes and set screws are applicable to Shaft Bores P, N, and C

[ ! ] Shaft Bore Specs. H (Round Hole), V or F (Stepped Hole), Y (Both Sides Stepped Hole) and WB (Two-stepped Hole) do not have tapped holes and set screws.
It may have a relief in the tapped hole depending on its size.

[ ! ] Due to vibrations during transportation, the set screw may become detached from the main body.
[ ! ] The tolerance of the tap position dimension from the boss end face and pulley end face is ±0.3.
[ ! ] Unless otherwise specified except for teeth and F dimensions, the dimension tolerance conforms to JIS B 0405 Class m.

Shaft Bore Specification Select shaft bore spec mark and each dim. from the table below.
[ ! ] Surface treatment may not be applied to the shaft bores.
[ ! ] Shaft Bore Dia. 4.5 and 6.35 are selectable within Shaft Bore Dia. d for Shaft Bore Specs. H, P, V and F.
[ ! ] Specify NK10 if keyway width of 4.0 mm (height 1.8 mm) for shaft bore spec. N and shaft bore diameter of 10 is desired.
[ ! ] For A-Shape pulley with shaft bore spec. P, N, or C, the screw holes are set at around 90° to keep away from peaks.

H round hole

P Round Hole + Tap

N New JIS Keyway + Tap
C Old JIS Keyway + Tap

V stepped hole

F Stepped Hole (Counterbored Hole on the Hub Side)

Y Both Ends Stepped Hole

WB Two-stepped hole

[!] Shape A: 2 ≤ J ≤ W－2, Shape B: 2 ≤ J ≤ L－2

[ ! ] Applicable to Shape B only
[ ! ] Z－F (d) ≥ 2
[ ! ]2 ≤ J ≤ L－2

[ ! ] Applicable to Shape A only
[ ! ] Q (R)－Y (d) ≥ 2
[ ! ]S+T ≤ W－3
[ ! ]S (T) ≥ 3

[ ! ] Applicable to Shape A only
[ ! ]Q－R ≥ 2
[ ! ] R－WB (d) ≥ 2
[ ! ]S+T ≤ W－3
[ ! ]S (T) ≥ 3

Type	Belt Width			[M] Material		[S] Surface Treatment	[A] Accessory Set Screws
	4 mm	6 mm	10 mm	Pulley	Flange
	P2M040	P2M060	P2M100	Pulley	Flange
PTPA	●	●	●	High Strength Aluminum Alloy	Aluminum alloy	Clear Anodize	SUS304
PTPB	●	●	●			Black Anodize
PTPK	●	●	●			Hard Clear Anodize
PTPN	●	●	●			Electroless nickel plating
PTPS	●	●	●	SUS304	SUS304	—	SUS304

[ ! ] Flange is installed.