Flat Belt Conveyors - Head Drive, 2-Groove Frame (Pulley Dia.30mm)

Brand :

MISUMI

Caution

Items with L Length longer than 2,000mm will be treated as special delivery from 01/11/02019,
and additional cost RM2,772.70 will be added in each product for the delivery fee. For items L Length shorter than 2,000mm will not have any price increase
[Discontinuation Information] The "HY (Yellow Green)" belt specification has been discontinued on March 3, 2025. There is no successor product, so please select another belt type.

Product Description

Panasonic and Oriental Motor cannot be selected as of now for motor selection due to unstable supply.

Dimensions

Frame cross section/enlarged (symmetrical)

[ ! ] JIS standard hex nuts can be used.

CVGA
6W motor specifications

For A*, see below.

25W motor specifications

*For L≧290, four nuts are inserted per groove. If countersunk holes for nut insertion are required, please specify this during additional processing.
[ ! ] The dimensions in the diagram are for belt specification H (thickness 0.9 mm). Please note that belt thickness varies depending on the belt specification. For belt specifications, please see >>here .
[ ! ] Depending on the usage environment, conveyance problems may occur.
[ ! ] For L≧1000, we recommend installing a stand. For details on additional stand processing, please see >>here .
[ ! ] For instructions on searching for maintenance parts (component list) , please see >>here .

■Transportation capacity

*Reference value

[ ! ] Accumulator conveyor (sliding belt

(applies only to the graph)

Please consider the transport capacity.

[ ! ] Conveying capacity varies depending on usage conditions

There may be cases where this is the case.

[ ! ] This graph shows the transport capacity under horizontal conditions.

Gearhead reduction ratio
*May decrease depending on load conditions.

*Reference value

Gearhead reduction ratio	Belt speed (m/min)
Gearhead reduction ratio	50Hz	60Hz
5	56.4	67.7
7.5	37.6	45.1
9	31.3	37.6
12.5	22.6	27.1
15	18.8	22.6
18	15.7	18.8
twenty five	11.3	13.5
30	9.4	11.3
36	7.8	9.4
50	5.6	6.8
60	4.7	5.6
75	3.8	4.5
90	3.1	3.8
100	2.8	3.4
120	2.4	2.8
150	1.9	2.3
180	1.6	1.9

[ ! ] For the IM motor model, the conveying speed is constant at the value shown in the table above.
[ ! ] For the SCM motor model, refer to the value shown in the table above for the maximum speed.

Conveyor Groove Applicable Nut

Insertion position	For L≧290, already inserted into the grooves on the conveyor side (4 pieces/groove). Additional counterbore holes (FYA/FYB) can be added (sold separately).				Post-insertion nuts (sold separately) can be inserted without processing or disassembly
Insertion position	Product name	Model number	Thread nominal	pitch	Product name	Model number	Thread nominal	pitch
X section	JIS Class 1 Hexagon Nut	LBNR3	M3 (coarse)	0.5	-
Y section	JIS Class 1 Hexagon Nut	LBNR6	M6 (coarse)	1.0	Post-assembly nuts for conveyors (10 pcs)	PACK-CHNT6-5	M5 (coarse)	0.8
	-					PACK-CHNT6-4	M4 (coarse)	0.7
	-					PACK-CHNT6-3	M3 (coarse)	0.5

Oriental Motor Speed Controller Dimensions
6W/25W Common

Taiwan Motor Speed Controller Outline Drawing

[ ! ] The speed control motor does not come with a mounting bracket for the speed controller.
If you require a bracket for the speed controller, please select the alteration [SCB].
[ ! ] If you wish to purchase the speed controller bracket separately, please enter the model number [P1-JTEA-12049072] on the " Quote/Order " screen.
[ ! ] There is no input terminal for controlling the speed controller externally.

*Details of A dimension (total motor length)

Output (W)	motor		Reduction ratio	A
	specification	Manufacturer
6W	Induction motor	Oriental Motor	12.5-18	105.0
			25 to 180	115.0
		Made in Taiwan	12.5〜75	114.7
			90-180	120.7
	Speed Control Motor	Oriental Motor	12.5-18	115.0
			25 to 180	125.0
		Made in Taiwan	12.5〜75	126.9
			90-180	132.9
25W	Induction motor	Oriental Motor	5 to 18	117.0
			25 to 180	127.5
		Made in Taiwan	5 to 75	129.0
			90-180	136.0
	Speed Control Motor	Oriental Motor	5 to 18	127.0
			25 to 180	137.5
		Made in Taiwan	5 to 75	139.5
			90-180	146.5

	frame	Motor cover	Pulley holder
[M]Material	Aluminum material	Aluminum material	Aluminum material
[S] Surface Treatment	Anodized aluminum treatment	coating	coating

■Machine weight
(motor output 6W) (kg)

	Pilot length L (mm)
Belt width B (mm)	500	750	1000	1500	2000
50	4.2	5	5.7	7.1	8.7
100	4.9	5.8	6.6	8.4	10.2
150	6.1	7.3	8.5	10.9	13.3
300	7.4	8.9	10.4	13.4	16.3

*The values in the table are for reference only. They may change depending on the belt type, additional processing, etc.
*If the motor output is 25W, add 1.1kg.

Additional work

Additional work details

Applicable conditions

Example of specification

code

Motor position reversed

The motor position can be changed.
Only head drive type can be specified.
<Specifying method>: MK

[ ! ]
For some models, adding MK will also
change related parts.

CVGA-100-1000-25-T100-
IM-25-HB-MK

FYA
FYB

Additional counterbore holes

Head drive

Additional counterbore holes for inserting nuts
are machined into the front and back frames.
<How to specify>: FYA300 FYA300-FYB600

Compatible conveyors	FYA/FYB
CVGA/CVGB	150≦FYA・FYB≦(L-60)

[ ! ] FYA・FYB = Specify in 5mm increments
[ ! ] FYB-FYA≧15
[ ! ] The specified range is as shown in the table on the left.

CVGA-100-1000-25-T100-
IM-25-HB-FYA500

Motor cover window type
head drive

It can be changed to a motor cover with a window.
<How to specify>: CW

[ ! ] Resin plates
can also be purchased separately for maintenance. Click here
for details .

CVGA-100-1000-25-T100-
IM-25-HB-CW

Additional work

Additional work details

Applicable conditions

Example of specification

code

SCB

Bracket for speed controller included

<Speed controller bracket specification drawing>
① Speed controller bracket

A mounting bracket for the speed controller
is included.
<How to order>: SCB

[ ! ] Two bracket mounting screws are included.
[ ! ] Two controller mounting screws (M4x8) are included .
[ ! ] Depending on the conveyor, installation
may not be possible due to space constraints.
[ ! ] The bracket shape varies depending on the conveyor model and motor specifications .

CVGA-100-1000-25-
T100-SCM-25-HB-SCB

ANT□

Post-insertion nuts included

Includes post-assembly nuts for Misumi conveyor frame grooves .
Material: SUS316 equivalent, sintered.
<How to order>: ANT6-Q8-4

[ ! ] Click here for details on post-assembly nuts

Code	Nut quantity Q	M	Accessory (1 piece)	A	B	T
			Set screw
ANT5	4 8 12	3	M4×5	4.9	7	4
(For M5 groove)		4
ANT6		3	M4×6	5.9	8	4.5
(For M6 groove)		4
		5

CVGA-100-1000-25-
T100-SCM-25-HB-
ANT6-Q8-4

TBM

Motor with terminal box
■ Oriental Motor specifications

Change the induction motor to a type with a terminal box .
<How to specify>: TBM

[ ! ] Only Oriental Motor specifications are available.

CVGA-100-1000-25-
T100-SCM-25-HB-TBM

Additional work

Added conveyor stand

Applicable conditions

Example of specification

code

NA□

■Conveyor stand I-type
belt width ≦ 140mm
(adjuster bolt type, stand base + reinforcement material)

*1 D dimension correspondence table

B	30 to 80	90 to 140
D	200	280

[ ! ] B is the belt width

Add a conveyor stand to the conveyor.
<How to specify>:
NA1-H750-PN
WA3-H1200-P400

[ ! ] Bolts and nuts matching the conveyor body groove size are included.
[ ! ] When the length between pulleys (L) is ≥ 1000, we recommend installing two or more stands
.
[ ! ] This specification adds (□-1) units of the part indicated by the dashed line in the drawing to one conveyor stand
.
[ ! ] The delivery time is the same as the standard delivery time for the conveyor.

		①Bracket	②Aluminum frame	③Adjusting bolt	④Aluminum frame
[M]Material	NA	SUS304	Aluminum material	steel	Aluminum material
	WA	steel
[S] Surface Treatment	NA	2B	Anodized aluminum treatment	Trivalent chromate	Anodized aluminum treatment
	WA	Trivalent chromate
		⑤Bracket	⑥Receiving plate	⑦Foot base
[M]Material	NA	Aluminum material	steel	-
	WA			steel
[S] Surface Treatment	NA	Anodized aluminum treatment	Trivalent chromate	-
	WA			Trivalent chromate

■NA□・WA□Installation Dimensions Table

Compatible models	C	X and Y
CVGA/CVGB	twenty one	B+37

*B is the belt width, C is the dimension to the conveying surface
*The mounting location is the dimension assuming a lower groove

Code	Number of stands	Height H	Pitch P
NA	1
WA	2	300～	300～
	3	1300	2000
	4

[ ! ] H and P dimensions can be specified in 10mm increments

[ ! ] If □=1, ④ aluminum frame and
⑤ bracket are not included.
[ ! ] If □=1, the stand will not stand on its own.
[ ! ] If □≧2 and ④ aluminum frame is not required, please order the CSTS and CSTW separately
instead of this additional modification . ( Here , and here ) [ ! ] The stand will be shipped in separate parts . Assembly is required by the customer .

CVGA-100-1000-25-T100-
SCM-25-HB-NA1-H800-PN

WA□

■Conveyor stand H type
belt width ≧ 150 mm
(adjustable bolt type, stand base + reinforcement material)

CVGA-200-1000-25-T100-
SCM-25-HB-WA2-H800-P500

Precautions

Reverse transport is not recommended.
This product is not waterproof.