Ball Splines Round Flanged, One End Double Stepped and Threaded

 

Type of Spline Shaft	Dh8	L 1mm increments	P Selection												F 1mm increments	M (Coarse) Selection (M≤P)										B 1mm increments
E-BSKM	8	60~300		4	5	6									When P＝4, 4≤F≤16 When P≥5, 4≤F≤P×5 F≥B+2		4	5	6							When M=4, 2≤B≤16 When M≥5, 2≤B≤M×5 B≥Pitch×3+ℓ
	10	60~400		4	5	6	8										4	5	6	8
	13	60~400			5	6	8	10										5	6	8	10
	16	70~600			5	6	8	10	12	13									6	8	10	12
	20	80~700					8	10	12	13	15	16	20						6	8	10	12	16
	25	90~900					8	10	12	13	15	16	20						6	8	10	12	16	20
	30	100~900						10	12	13	15	16	20	25						8	10	12	16	20	24

 

Type of Spline Shaft	Dh8	D1		D2	L1	H	W	P.C.D	X	Y	Z	u	Basic Rated Torque		Basic Load Rating		Static Allowable Moment
													Dynamic Ct (N·m)	Static C0t (N·m)	Dynamic C (kN)	Static C0 (kN)	M01 (N·m)	M02 (N·m)
			Tolerance
E-BSKM	8	16	0 -0.027	32	27	8	7.5	24	3.4	6.5	4.5	1.5	3.3	6	0.8	1.4	3.5	25.2
	10	21	0 -0.033	42	33	9	10.5	32	4.5	8	4		13.3	23.8	2.6	3.9	9.5	85.3
	13	24		44	36		11	33			4.5		19.6	36.4	3.2	5.4	15	124.6
	16	31	0 -0.039	51	50	10	18	40			6	2	35.7	65.1	4.3	7.7	37.1	260
	20	35		58	56			45	5.5	9.5	5.4		59.5	107.8	5.9	10.7	55.3	380
	25	42		65	71	13	26.5	52			8	3	135.1	243.6	10	15	103.5	685.9
	30	47		75	80		30	60	6.6	11			190.4	343	11	19.6	148.4	932.7

When Spline Shaft ④ is configured, the surface will be light yellow, and there may be a color difference.
  Due to the surface treatment process, the following parts are more susceptible to rust.
  -Cut section
  -Groove part
  -Cut section
The relative positions of the grooves of Spline Shaft, the keyways and oil holes of nuts, and all the alterations (wrench flat, set screw flat, etc.) in the 3D modelare for reference only and may differ from their actual positions.
 

■Ball Screws

Precision Ball Screws
Φ8	Φ10	Φ12	Φ15	Φ20	Φ25

 

Rolled Ball Screws
Φ8	Φ10	Φ12	Φ15	Φ20	Φ25

■Precautions for Selection and Use of Spline Shaft
1. The relative positions of the grooves of Spline Shaft, the keyways and oil holes of straight nuts, and all the alterations (wrench flat, set screw flat, etc.) in the 3D model are for reference only and may differ from their actualpositions.
2. When re-inserting a nut into the Spline Shaft, be sure to insert it horizontally, otherwise the ball will fall off.
3. As resin parts are used inside the nuts, please use them at temperatures below 80℃.
4. Although the nuts are greased on the inside before leaving the factory, please re-grease them every 2~3 months or every 50km of traveling distance after receipt of the goods, otherwise their use will be impaired.
5. No guarantee is given for the noise level of this product.
6. No guarantee is given that the Spline Shaft or nuts of this product will fall freely.
7. This product is a machined type, so there will be knife patterns and color difference in its appearance. It is normal for the product to have some scratches or color changes. Please feel free to use.
8. The Spline Shaft is quenched, and annealed during machining.
  Due to the annealing treatment, the hardness of the machined part + area about 15 mm before and after the part may be reduced (see the following example). And the annealed section is out of the guaranteed range of outerdiameter dimensional tolerance.
  Subtract the size of the annealed section when calculating the stroke.

When ④ is configured, the surface will be light yellow, and there may be a color difference.
  Due to the surface treatment process, the following parts are more susceptible to rust.
  -Cut section
  -Groove part
  -Cut section
The relative positions of the grooves of spline shaft, the keyways and oil holes of nuts, and all the alterations (wrench flat, set screw flat, etc.) in the 3D model are for reference only and may differ from their actual positions.
 

Unit: μm