Rolled Ball Screws - Shaft Dia. 6; Lead 1 / 2 / 6 / 10 - Accuracy Grade C7

Brand :

MISUMI

Caution

Product Description

Product Overview of Ball Screw

1. This series of products is the C7 Rolled Ball Screw with the shaft diameter of 6 and lead of 1/2/6/10.
2. It is more suitable for feeding mechanisms in FA automation equipment.
3. The Ball Screw end is machined according to standard specifications. If the shaft end requires alteration, it should be specified according to the catalog.

Dimensional Drawing of Ball Screw

Accuracy grade	Ball Screw Dia.	Lead	Ball Screw			Nut
Accuracy grade	Ball Screw Dia.	Lead	Material of Ball Screw	Hardness	Surface Treatment	Material of Ball Screw	Hardness	Surface Treatment
C7	6	1·2·6·10	S55C equivalent	Induction hardening 58～62HRC	－	SCM415H equivalent	Carburized 58～62HRC	－

Specification Table of Ball Screw

Part Number of Ball Screw			L (1mm increments)	Y	Number of Circuits	Basic Load Rating		Axial Play	Twisting Direction
Type of Ball Screw	Ball Screw O.D.	Lead				C (Dynamic) kN	C (Static) kN
E-TBS	06	01	60~170	L-25	3 turns	0.56	0.95	0.02 or Less	Right
		02			3 turns	0.75	1.2
		06			3.2 turns	0.87	1.45
		10			2.4 turns	0.95	1.6

Alterations of Ball Screw

		Part Number (Type·Ball Screw O.D.·Lead)	－	L	－	(RLC·SZC…etc.)
		E-TBS0601	－	80	－	RLC

■Support side of Ball Screw

Alterations

Code

Spec.

①Ball Screw Orientation Reversed

RLC

Changes the Ball Screw direction.
Ordering CodeRLC

②Machining on Support Side Shaft End
Ball Screw

TFC

Machining added on the support Ball Screw end.
Ordering Code TFC

d	φ4
d₁	φ3.7_±0.03
ℓ	5.35_±0.05
ℓ₁	0.5

When ⑤ and ⑥ are specified simultaneously, no male thread will be machined regardless of the value specified for U in ⑤.

When specifying any alteration, the nut motion range (Y dimension) may become shorter. Please make sure that the Ball Screw motion range is greater than the full length ofthe Ball Screw.

■Fixed side of Ball Screw

Alterations of Ball Screw	Code of Ball Screw	Spec of Ball Screw.
③Wrench Flats on Ball Screw Incomplete Hardened Area	SZC	Adds wrench flats on the fixed Ball Screw end. Ordering CodeSZC Ball bearings will fall out if the Ball Screw crosses the wrench flats. The Ball Screw may not be moved within the Incomplete Hardened Area. Note that when selecting.
④No machining of small steps on the Ball Screw	NF	No machining of small steps on the Ball Screw Ordering CodeNF
⑤Change dimensions of big steps on the Ball Screw	CU	Change dimensions of big steps on the Ball Screw 7≤C≤22 4≤U≤C－3 C, U＝1mm increments Ordering CodeCU-C15-U10
⑥No machining of big steps male thread on the Ball Screw	NU	No machining of big steps male thread on the Ball Screw Ordering CodeNU

Ball Screw Runout Tolerance

Type	Ball Screw Shaft O.D.	Runout tolerance G (Max.)											Incomplete Hardened Area (ℓ)
Type	Ball Screw Shaft O.D.	~125	126~200	201~315	316~400	401~500	501~630	631~800	801~1000	1001~1250	1251~1600	1601~2000	Incomplete Hardened Area (ℓ)
E-TBS	4	0.060	0.075	-	-	-	-	-	-	-	-	-	5
E-TBS	6	0.075	0.075	-	-	-	-	-	-	-	-	-	5
C-TBSE C-TBSB	8	0.100	0.140	0.210	0.270	-	-	-	-	-	-	-	10
	10	-	0.120	0.160	0.210	0.270	0.350	-	-	-	-	-
	12	-	0.120	0.160	0.210	0.270	0.350	0.480	-	-	-	-
	15	-	0.110	0.130	0.160	0.200	0.250	0.320	0.420	0.550	-	-
	20	-	0.110	0.130	0.160	0.200	0.250	0.320	0.420	0.550	0.730	0.730	15
	25	-	0.110	0.110	0.130	0.160	0.190	0.230	0.300	0.380	0.500	0.690	15
	32	-	-	0.110	0.130	0.160	0.190	0.230	0.300	0.380	0.500	0.690	20
E-KBS	4	0.050	-	-	-	-	-	-	-	-	-	-	5
E-KBS	6	0.050	0.050	-	-	-	-	-	-	-	-	-
C-KBS	8	0.060	0.075	0.100	-	-	-	-	-	-	-	-
	10	0.055	0.065	0.080	0.100	-	-	-	-	-	-	-
	12	-	0.065	0.080	0.100	0.120	-	-	-	-	-	-	10
	15	-	0.060	0.070	0.080	0.095	0.110	0.140	0.170	0.210	-	-	10
	20	-	0.060	0.070	0.080	0.095	0.110	0.140	0.170	0.210	0.270	-	15
	25	-	-	0.060	0.070	0.080	0.090	0.100	0.130	0.170	0.210	-	15
E-KLR	4	0.050	0.050	-	-	-	-	-	-	-	-	-	5
	8	0.065	0.075	0.100	-	-	-	-	-	-	-	-
	10	0.065	0.065	0.080	0.100	-	-	-	-	-	-	-

Ball Screw Runing Noise Level

Ball screw noise level is affected by several important factors:

The figures below show the noise levels of ball screws with different specifications.
Note:
- These test results are for reference only and do not represent all ball screw specifications.
- Actual noise levels may vary depending on multiple factors.
Misumi C7 grade ball screws have controlled outgoing noise levels and guarantee less than 70 dB at a rotational speed of 1500 RPM.
(Noise measured at a distance of 1 meter from the ball screw)

Product Features of Ball Screw

1. Drawing-based machining is no longer required, saving the time for drawing.
2. The total length of Ball Screw can be specified in 1 mm increments. With abundant shaft end specifications, it is possible to specify alterations for different applications.

Example Use of Ball Screw

Precautions of Ball Screw

■ Precautions for Selection and Use
● The noise value of the Ball Screw after assembly is not guaranteed.
● Although lithium soap-based grease has been applied at the factory, it is required to apply new grease every 2~3 months as standard after receiving the goods, otherwise the normal use will be affected.
●In operation, if there is too much noise or sharp and harsh sound, please make sure that the installation accuracy of the Ball Screw and the specifications of peripheral components such as motors and couplings are appropriate.
●Do not let the nut exceed the movement range of the ball screw nut, or screw out of the screw shaft, otherwise the ball will fall off and the ball cycling parts will be damaged.
● Ball Screw and nuts placed with an inclination may fall due to weight. Please be careful.
● This product is a machined type, so there will be knife patterns and color difference in its appearance. Small scratches or color changes without affecting the use and main function are of a normal phenomenon. Please feel free touse.

·Removal of nut is prohibited	·No impact on the Ball Screw	·Be careful of falling due to weight
·Checking for reverse action	·Pay attention to intrusion of foreign objects	·Ball Screw overstroke is prohibited

■ Precautions of the ball screw and peripheral parts design and assembly
The Ball Screw is a component that only bears axial load. If it is subjected to radial load or moment load, poor sliding, vibration or abnormal noise may occur, shortening its service life.
The reason that the Ball Screw bears radial load and moment load is the axis deviation and parallelism error of the surrounding parts. Therefore, it is necessary to correctly design and assemble the peripheral parts of the ball screwto prevent errors.
● Axis deviation of Ball Screw and support unit (Fig. 1)
- Axis deviation is the deviation of the Ball Screw fixed by the fixed side support unit and the bearing of the supporting side support unit.
-The allowable value of the axis deviation is 20μ or less (reference value)
●Parallelism between Ball Screw and linear guide (Diagram 2)
- Parallelism error refers to the inclination of the Ball Screw in the up-down or left-right direction with respect to the reference of the linear guide.
-The allowable value of inclination is below 1/2000 (Diagram 3)
●Precautions of assembly
If you notice abnormal noises during the operation of the Ball Screw or jamming during movement after assembly, please loosen the connections of the parts before proceeding. Adjust and reassemble after moving smoothly.
- Error in the left and right direction of the support unit (Fig. 1)
- Parallel error of linear guide and ball screw (Fig. 2)
- Fixing of workbench and nut bracket
- Fixing of ball screw nut and nut bracket

Brand Introduction

Since its establishment in 1963 in Japan, MISUMI Group Inc. has been providing customers with a wide range of high quality parts such as FA factory automation parts, mold parts, electronic parts, tools and consumables in a fast and accurate manner. We have created a low-cost business model by compiling our own catalogs and establishing a marketing system to sell our products directly, and we continue to develop MISUMI branded products with a high level of quality by developing an annual product plan based on customer feedback and requests. MISUMI established MISUMI Precision Machinery Co., Ltd. in China in June 2003, and then changed its name to MISUMI (China) Precision Machinery Trading Co., Ltd. in June 2007, with its headquarters in Shanghai. Since the beginning of the stamping die standard parts business, the businesses of FA standard parts, plastic die standard parts and machining tools have been officially started successively, and the rapid development of MISUMI in China has won the full support of customers. China's manufacturing industry has unlimited prospects, which is why China's manufacturing industry market has become one of the most competitive industries in the world. Thus was born MISUMI's business philosophy - the key to the future of manufacturing in China is cost competitiveness as well as "quality" and "time".