X-Axis Motorized Positioning Stages, Long stroke, Linear Ball Guide Type, Positioning Repeatability ±1μ

Brand :

MISUMI

Caution

Product Description

Product Overview

The MISUMI E-XMBSXH series electric slide table is an economical slide table equipped with a two-phase stepper motor. It can be used as a slide table for position adjustment in automated equipment. The main body is made of steel with electroless nickel plating, providing not only high rigidity but also excellent rust resistance. An integrated linear ball guide is used for guidance, meeting the required precision for use. By simplifying the structure and improving the manufacturing process, the price has been significantly reduced.

Dimensional Drawing

Material: Steel

Surface treatment: Chemical nickel plating

Specification Table

Type

Slide Table
Length
(mm)

Cover Plate
Position

Motor

Driver

Cable
Length
(m)

Mechanical Specifications

Accuracy Specifications

Sensor

Type

Travel distance
(mm)

Load capacity
(N)

Weight
(kg)

Resolution
(pulses)

Maximum
speed

Unidirectional
positioning
accuracy

Repeat
positioning
accuracy

Non-effective
movement

Parallelism

Straightness

Motion
parallelism

Limit
sensor

Origin sensor
(ORG1)

E-XMBSXH

X axis

6030

60 × 60

Blank
(with standard
stepper motor)

S1
(with servo bracket
PCD=45)

S2
(With servo bracket
PCD=46)

A
(single-axis pulse
driver)
N
(No driver)
E
(EtherCat bus driver)

2
(2-meter cable)

4
(4-meter cable)

117.6

1.28

5 µm

20 mm/sec

15 µm

±1 µm

2 µm

30 µm

3 µm

15 µm

Yes

6050

1.4

6075

1.54

60100

100

1.8

10µm

45 mm/sec

5 µm

60150

150

2.1

20µm

25µm

60200

200

2.42

7µm

8030

80 × 80

176.4

2.57

5 µm

20 mm/sec

15 µm

3 µm

15 µm

8050

2.76

5 µm

8075

3.1

80100

100

3.27

Driver: The pulse driver model used in this series is E-DR42C.

Bus driver brand and model: Leadshine DM3C-EC522.

Cable: The cable models used in this series are HRS12-2M (2-meter cable) / HRS12-4M (4-meter cable).

Servo motor mounting bracket type. Recommended motor brands: Yaskawa, Inovance, Mitsubishi, Leadshine, Moons, etc. Recommended power: 50W, 100W. Please carefully check the motor mounting dimensions.

■ General specifications

		E-XMBSXH6030	E-XMBSXH6050	E-XMBSXH6075	E-XMBSXH60100	E-XMBSXH60150
Feed screw		Ball screw ⌀8, lead 1 mm			Ball screw ⌀8, lead 2 mm
Guide rail		Linear ball guide type
Motor	Type	2-phase standard stepper motor 1.3 A/phase			2-phase high-torque stepper motor 1.3 A/phase
	Step angle	1.8°
Pulse driver	Power supply voltage	24 to 36 V DC
	Output current	0.3 A to 2.2 A/phase (peak)
	Pulse signal voltage	5VDC
	Pulse input mode	Pulse + direction or dual pulse
	Microstep settings	200 to 25600
Connector	Type	HR10A-10R-12P (Hirose)
	Receiver side type	HR10A-10P-12S (Hirose)
Sensor board	Power supply voltage	24 V DC ±10%
	Sensor type	Miniature photo sensor RPI-0125 (ROHM)
	Control output	NPN open collector output
	Output logic	When detected (light blocked): output transistor OFF (not conducting)

		E-XMBSXH60200	E-XMBSXH8030	E-XMBSXH8050	E-XMBSXH8075	E-XMBSXH80100
Feed screw		Ball screw ⌀8, lead 2 mm	Ball screw ⌀8, lead 1 mm
Guide rail		Linear ball guide type
Motor	Type	2-phase high-torque stepper motor 1.3 A/phase	2-phase standard stepper motor 2.0 A/phase
	Step angle	1.8°
Pulse driver	Power supply voltage	24 to 36 V DC
	Output current	0.3 A to 2.2 A/phase (peak)
	Pulse signal voltage	5VDC
	Pulse input mode	Pulse + direction or dual pulse
	Microstep settings	200 to 25600
Connector	Type	HR10A-10R-12P (Hirose)
	Receiver side type	HR10A-10P-12S (Hirose)
Sensor board	Power supply voltage	24 V DC ±10%
	Sensor type	Miniature photo sensor RPI-0125 (ROHM)
	Control output	NPN open collector output
	Output logic	When detected (light blocked): output transistor OFF (not conducting)

■ Connector pin arrangement

■ Timing diagram
Pulse driver

Product Features

Feature 1: The limit sensor is installed inside the main body, so it does not protrude from the side of the slide table, saving space.
Feature 2: Localized production and optimized structure enable a low price.
Feature 3: Additional positioning holes on the slide table surface allow for quick assembly and disassembly.
Feature 4: The main body is made of steel with a chemical nickel plating, providing not only high rigidity but also excellent rust resistance.

Usage Method

The E-XMBSXH series X-axis slide table is equipped with a two-phase stepper motor and requires use with a MISUMI two-phase stepper motor driver, cable, as well as a customer-supplied 24 V power supply and host controller (PLC or motion control card). An example of the connections between each product is shown in the figure below. A servo motor can also be used (motor mounting holes PCD45 or PCD46).

Wiring diagram

Precautions

■ Slide Table Operating Environment
Operating environment: 10 to 50°C, 20 to 70% RH (non-condensing)
Recommended environment: 22±5°C, 20 to 70% RH (non-condensing)
Please avoid using the slide table in the following environments
(1) Dusty environments (especially metal powder)
(2) Environments with direct sunlight or heat radiation
(3) Near fire sources
(4) Environments with corrosive or flammable gases
(5) Environments with splashing water or oil
(6) Environments with strong vibration or impact
(7) Environments with organic solvents or high salt content

■ Maintenance of the Slide Table
There is no unified regular maintenance standard due to differences in grease types and operating environments. Depending on the drive conditions and the type of guide rail, please be sure to check the grease at least once a month.

Application Industries

Electronics/Home Appliances	Automotive	Medical

Smartphones	Semiconductors	Lithium batteries

		Direction of movement
		X axis	Rotary axis	Goniometer	Z axis	Multi-axis combination
Guide mechanism	Linear ball	Thin type, repeatability ±1.5µ Standard type, repeatability ±1µ Standard type, repeatability ±1.5µ With recirculator, standard type, repeatability ±1.5µ/±2µ With recirculator, standard type, repeatability ±1µ With recirculator cover, standard type, repeatability ±1µ Repeatability ±5µ	—	—	Lifting type Repeatability ±5µ Repeatability ±5µ	Repeatability ±5µ
Guide mechanism	Crossed roller	Repeatability ±1.5µ Repeatability ±1µ	—	Repeatability ±0.006° Repeatability ±0.01°	Repeatability ±1µ	Repeatability ±0.01°
Displacement mechanism	Ball screw	—	Repeat positioning accuracy ±0.005° Repeat positioning accuracy ±0.01°	—	—	—
Displacement mechanism	Worm gear and worm	—	Repeatability ±0.05° Repeatability ±0.08°	—	—	—