Flat Belt Conveyor, Head Drive, High Load Type, Pulley Dia. 50mm
Brand :
MISUMI
Caution
- This single-phase motor is specified for 220V ±10%,50Hz/60Hz. Please ensure it is used within the permissible voltage range.
Product Description
Economy series Belt Conveyor
Dimensional Drawing
E-CVSH/E-CVSG
Standard nut allocation table for profile groove: L value (center distance unit: mm)
Nuts are shipped with the conveyor as accessories and are not displayed in the CAD model.
Nuts order quantity 1 = 1 pack (50 pcs/pack)
Test motor: Leadshine (LS) Timing pulley transmission ratio 1:1
Belt width: B=400 mm, thickness 2.0 mm Roller center distance: L=1000 mm
Motor specifications: 200W*
Default conveying direction Enlarged view of profile cross-section
(symmetrical left and right)
Default conveying direction Enlarged view of profile cross-section (symmetrical left and right)
*Differences in power only affect the motor size. For the A dimension, please refer to the table below. The external dimensions of the other parts remain the same.
Standard nut allocation table for profile groove: L value (center distance unit: mm)
| L600 to 999 | L1000 to 1499 | L1500 or more | Specification | Configuration Type |
| 16PCS | 24PCS | 32PCS | M6 (T shape) / E-TNT8-40-6(50) | Accessory |
Nuts are shipped with the conveyor as accessories and are not displayed in the CAD model.Nuts order quantity 1 = 1 pack (50 pcs/pack)■ A dimension detail table (speed regulation/inverter motor)
| Motor Power | Motor | Reduction Ratio | A | |
| Specification | Manufacturer | |||
| 120W | Inverter type | GPG | 3 to 18 | L183 |
| 25 to 180 | L201 | |||
| Speed regulation type | 3 to 18 | L194.5 | ||
| 25 to 180 | L212.5 | |||
| Inverter type | JSCC | 3 to 18 | L196 | |
| 25 to 180 | L216 | |||
| Speed regulation type | 3 to 18 | L207 | ||
| 25 to 180 | L227 | |||
| 200W | Inverter type | GPG | 3 to 18 | L230 |
| 25 to 180 | L230 | |||
| Speed regulation type | 3 to 18 | L240.5 | ||
| 25 to 180 | L240.5 | |||
| Inverter type | JSCC | 3 to 18 | L219 | |
| 25 to 180 | L243 | |||
| Speed regulation type | 3 to 18 | L231 | ||
| 25 to 180 | L255 | |||
■ A dimension detail table (stepper motor)
■ A dimension detail table (planetary reducer)
When a stepper motor or servo motor is selected and a planetary reducer is configured, the A dimension shown in the diagram is the sum of the motor A dimension and the planetary reducer A dimension.
| Brand | Motor Model | A |
| Leadshine stepper motor (open loop) | 86CM45 | L80 |
| 86CM80 | L98 | |
| 86CM120 | L129 |
■ A dimension detail table (planetary reducer)
| Gear Ratio (x) | Supported Motor Specification | A |
| 3 5 10 | Equipped with an 86 stepper motor | L110 |
| 15 20 25 30 | L130 |
When a stepper motor or servo motor is selected and a planetary reducer is configured, the A dimension shown in the diagram is the sum of the motor A dimension and the planetary reducer A dimension.Specification Overview
■ Material table
■ Flat belt width - pulley center distance correspondence table
| Part name |  Material |  Surface Treatment |
| Profile | Aluminum | Anodized |
| Motor cover | Aluminum | Spray coating and baking |
| Pulley holder | Aluminum | Spray coating and baking |
■ Flat belt width - pulley center distance correspondence table
| Model | Belt Width B | Pulley Center Distance L | |||
| L600 to 1500 | L1505 to 2000 | L2005 to 2500 | L2505 to 3000 | ||
| E-CVSH E-CVSG | 100 to 200 | ● | ● | ● | ● |
| 205 to 400 | ● | ● | ● | ● | |
| 405 to 600 | ● | ● | ● | ● | |
| 605 to 800 | ● | ● | ● | ● | |
Specification Table
Please follow the selection procedure 
to 
, select the type and parameters, and then proceed with ordering.
■ Specification Table
■ Speed control/inverter type
When there is no gear head and the gear head reduction ratio is ≤ 10, the drive side uses timing belt transmission; when the gear head reduction ratio is > 10, the drive side uses chain transmission.
When selecting the INV inverter motor, the inverter is delivered together as an accessory.
■ Stepper type
When using an 86 stepper with a torque of 4.5 N⋅m, the driver supports an input voltage of 48 V DC. (Power supply not included)
When using an 86 stepper with a torque of 8.0 N⋅m or 12.0 N⋅m, the driver supports an input voltage of 24 V DC to 70 V DC or 48 V AC to 70 V AC, two types of power supply voltage. (Power supply not included)
The drive side uses timing belt transmission.
The belt thickness is the nominal thickness; the actual thickness is one-tenth of this value, with the unit in mm.
For oil resistance specifications, only the transmission surface is oil resistant. If oil gets on the back of the belt, it may become unusable.
When selecting without motor and without gear head, the motor installation hole pitch will vary depending on the motor output power.
When selecting without motor and without gear head, the main unit will be delivered as parts. Please assemble by the customer according to the assembly procedure instruction manual included in the same package.
For belts other than those above, please refer to the specification overview by clicking 
here.
Table 1: Deceleration head reduction ratio & transmission capacity (speed regulation/inverter motor)
■ Deceleration head reduction ratio-speed correspondence table
INV inverter type: Reference value for flat belt speed when the motor speed is 1300 rpm (50 Hz).
to 
, select the type and parameters, and then proceed with ordering. | Type | - |  Belt Width B | - |  Pulley Center Distance L | - | Motor Selection | - |  Belt Specification | - | Motor Manufacturer Selection | ||||
 Output power | - |  Specification | - |  Gear Head Reduction Ratio | |||||||||||
| When there is no pulley When there is no motor or gear head | E-CVSG E-CVSG E-CVSG | - - - | 300 300 300 | - - - | 2000 2000 2000 | - - - | 120 120 120 | - - - | SCM INV NM | - - - | 25 25 NH | - - - | H20 J H20 | - - - | G G R |
■ Specification Table
| Type | Type | Machine Characteristics |
| E-CVSH | Arc-shaped roller anti-deviation | Good belt flatness and high surface accuracy |
| E-CVSG | Belt with guide strip for deviation prevention | Belt deviation prevention is stable, but there is a slight bulge at the bonding area of the center guide strip on the flat belt |
■ Speed control/inverter type
| Type | B Specified unit 5 mm | L Specified unit 5 mm | Motor Selection | Belt Specification (Material is generally PU) | Motor | ||
| Torque (N⋅m)//Power (W) | Specification/Drive Method | Gear Head Reduction Ratio | |||||
| E-CVSH (Arc-shaped roller type) E-CVSG (With guide strip type) | 100 to 800 | 600 to 3000 | 120 200 (Power W) | SCM (Single-phase 220 V speed regulation type) | 5 7.5 10 12.5 15 18 25 30 36 50 60 75 90 100 120 150 180 | H20(general use · green PVC) W20(general use · white PVC) U13(sliding · green PVC) S13(sliding · white PVC) D20(anti-static · green PVC) F15(for food conveying · white PU) O14(oil-resistant specification · green PU) Y20(general use · yellow PVC) V20(general use · red PVC) J(without belt) | G(GPG - Taibang motor) J(JSCC - Jingyan motor) |
| INV (3-phase 220 V inverter type) | |||||||
| NM(without motor) | NH(without gear head) | R(without motor and gear head) | |||||
When there is no gear head and the gear head reduction ratio is ≤ 10, the drive side uses timing belt transmission; when the gear head reduction ratio is > 10, the drive side uses chain transmission. When selecting the INV inverter motor, the inverter is delivered together as an accessory.■ Stepper type
| Type | B Specified unit 5 mm | L Specified unit 5 mm | Motor Selection | Belt Specification (Material is generally PU) | Motor | ||
| Torque (N⋅m)//Power (W) | Specification/Drive Method | Gear Head Reduction Ratio | |||||
| E-CVSH86 (Arc-shaped roller type) E-CVSG86 (with guide strip type) | 100 to 800 | 600 to 3000 | 4.5 8.0 12.0 (86 stepper type / torque N⋅m) | MC (pulse universal type) IO (IO control type) EC (EtherCAT bus) RS (RS485 communication) | 3 5 10 15 20 25 30 NH (without gear head) Caution: 3 to 10 are single stage | H20(general use · green PVC) W20(general use · white PVC) U13(sliding · green PVC) S13(sliding · white PVC) D20(anti-static · green PVC) F15(for food conveying · white PU) O14(oil-resistant specification · green PU) Y20(general use · yellow PVC) V20(general use · red PVC) J(without belt) | LS (Leadshine motor) |
| NM (without motor and driver) | R (without motor, driver, and gear head) | ||||||
When using an 86 stepper with a torque of 4.5 N⋅m, the driver supports an input voltage of 48 V DC. (Power supply not included)When using an 86 stepper with a torque of 8.0 N⋅m or 12.0 N⋅m, the driver supports an input voltage of 24 V DC to 70 V DC or 48 V AC to 70 V AC, two types of power supply voltage. (Power supply not included)The drive side uses timing belt transmission.The belt thickness is the nominal thickness; the actual thickness is one-tenth of this value, with the unit in mm.For oil resistance specifications, only the transmission surface is oil resistant. If oil gets on the back of the belt, it may become unusable.When selecting without motor and without gear head, the motor installation hole pitch will vary depending on the motor output power.When selecting without motor and without gear head, the main unit will be delivered as parts. Please assemble by the customer according to the assembly procedure instruction manual included in the same package.For belts other than those above, please refer to the specification overview by clicking 
here.Table 1: Deceleration head reduction ratio & transmission capacity (speed regulation/inverter motor)
■ Transmission capacity
Test motor: JSCC (J) timing pulley transmission ratio 1:1
Belt width: B=600 mm, thickness 2.0 mm Roller center distance: L=3000 mm
Test motor: JSCC (J) timing pulley transmission ratio 1:1Belt width: B=600 mm, thickness 2.0 mm Roller center distance: L=3000 mm
■ Deceleration head reduction ratio-speed correspondence table
INV inverter type: Reference value for flat belt speed when the motor speed is 1300 rpm (50 Hz). | Gear head reduction ratio | Flat belt speed (m/min) | |
| SCM speed regulation type | INV inverter type | |
| 5 | 42.2 to 67.8 | 39.2 to 65.3 |
| 7.5 | 28.1 to 46.9 | 26.1 to 43.5 |
| 10 | 21.1 to 35.2 | 19.6 to 32.7 |
| 12.5 | 16.9 to 28.1 | 15.7 to 26.1 |
| 15 | 14.1 to 23.4 | 13.1 to 21.8 |
| 18 | 11.7 to 19.5 | 10.9 to 18.1 |
| 25 | 8.4 to 14.1 | 7.8 to 13.1 |
| 30 | 7.0 to 11.7 | 6.5 to 10.9 |
| 36 | 5.9 to 9.8 | 5.4 to 9.1 |
| 50 | 4.2 to 7.0 | 3.9 to 6.5 |
| 60 | 3.5 to 5.9 | 3.3 to 5.4 |
| 75 | 2.8 to 4.7 | 2.6 to 4.4 |
| 90 | 2.3 to 3.9 | 2.2 to 3.6 |
| 100 | 2.1 to 3.5 | 2.0 to 3.3 |
| 120 | 1.8 to 2.9 | 1.6 to 2.7 |
| 150 | 1.4 to 2.3 | 1.3 to 2.2 |
| 180 | 1.2 to 2.0 | 1.1 to 1.8 |
Table 2: Correspondence table of load and linear speed (stepper motor)
| Speed (rpm) | Gear head reduction ratio | Max. linear speed (m/min) | Voltage 48 V DC (current 6 A) | ||
| 86CM45 | 86CM80 | 86CM120 | |||
| Load (kg) | |||||
| 100 | NH | 25.1 | / | / | / |
| 150 | 37.7 | / | / | / | |
| 200 | 3 | 16.7 | / | 6 | 8 |
| 5 | 10.0 | 13 | 30 | 35 | |
| 10 | 5.0 | 70 | 85 | 160 | |
| 15 | 3.3 | 110 | 130 | 200 | |
| 20 | 2.5 | 150 | 180 | 200 | |
| 25 | 2.0 | 185 | 200 | 200 | |
| 30 | 1.7 | 200 | 200 | 200 | |
Test motor: Leadshine (LS) Timing pulley transmission ratio 1:1Belt width: B=400 mm, thickness 2.0 mm Roller center distance: L=1000 mm
Alterations
 | Type | - | Belt Width B | - | Pulley Center Distance L | - | Motor Selection | - | Belt Specification | - | Motor Manufacturer Selection | - | Alteration | ||||
| Output Power | - | Specification | - | Gear Head Reduction Ratio | |||||||||||||
| E-CVSG | - | 300 | - | 2000 | - | 120 | - | SCM | - | 25 | - | H20 | - | G | - | MK | |
| Alterations | Code | Spec | ||||||
Reverse motor installation position | MK | The motor installation position can be changed. Ordering code MK Can only be specified for head drive type. | ||||||
Mounting bracket for speed controller | SCB | Comes with a mounting bracket for the speed controller. Ordering code SCB | ||||||
Conveyor belt reverse conveyance | FX | Reverse conveyance. Ordering code FX | ||||||
Conveyor belt bidirectional conveyance Only supports models with guide strips | SX | Bidirectional conveyance. Ordering code SX | ||||||
Increase the quantity of nuts in the profile groove Select only when the standard quantity is insufficient (see dimensional drawing information for standard quantity and specification) | ANQ | Increase the quantity of nuts in the profile groove. Ordering code ANQ5
|
Product Features
Feature 1: The conveyor body uses an aluminum profile, achieving an overall lightweight design.
Feature 2: Medium and heavy load, universal European standard 4080 profile makes it easy to build profile brackets, and is widely used in logistics lines.
Feature 3: The conveyor belt roller pitch has a wide selection range, can be specified in 5 mm increments, with a maximum pitch of up to 3 meters.
Feature 2: Medium and heavy load, universal European standard 4080 profile makes it easy to build profile brackets, and is widely used in logistics lines.
Feature 3: The conveyor belt roller pitch has a wide selection range, can be specified in 5 mm increments, with a maximum pitch of up to 3 meters.
Precautions
(1) Do not disassemble or modify the conveyor by yourself to avoid causing performance defects.
(2) Due to differences in the operating environment of the conveyor, MISUMI conveyors do not come with a power supply, cable, or switch.
(3) Due to issues with the structural strength and deformation of the machine body, please do not exceed the allowable load or length and width when selecting a model. For the deviation adjustment method, clickhere.
(4) The motor is available in two voltage specifications: single-phase 220 V and 3-phase 220 V. Please select the voltage according to your usage requirements.
(5) Belt deviation is a normal phenomenon and does not constitute a quality problem. Deviation adjustment is part of daily maintenance.
(6) Deviation tolerance: The distance from the belt to both sides of the roller should be 5+/-3mm. During operation, it is not possible to ensure that the belt always stays at the center of the aluminum profile.
(7) If the direction is opposite to the standard operating direction, belt deviation, belt breakage, noise, jamming, and other abnormalities may occur. Please avoid using it in this way. (The standard transport direction is shown in the figure below)
(2) Due to differences in the operating environment of the conveyor, MISUMI conveyors do not come with a power supply, cable, or switch.
(3) Due to issues with the structural strength and deformation of the machine body, please do not exceed the allowable load or length and width when selecting a model. For the deviation adjustment method, click
here.(4) The motor is available in two voltage specifications: single-phase 220 V and 3-phase 220 V. Please select the voltage according to your usage requirements.
(5) Belt deviation is a normal phenomenon and does not constitute a quality problem. Deviation adjustment is part of daily maintenance.
(6) Deviation tolerance: The distance from the belt to both sides of the roller should be 5+/-3mm. During operation, it is not possible to ensure that the belt always stays at the center of the aluminum profile.
(7) If the direction is opposite to the standard operating direction, belt deviation, belt breakage, noise, jamming, and other abnormalities may occur. Please avoid using it in this way. (The standard transport direction is shown in the figure below)
Application Industries
| Equipment Production | Semiconductor | Lithium Battery | ||
 |  |  | ||
| Food | Electronic & Electrical | Robot | ||
 |  |  |
Related Products
| Economy Flat Belt Conveyor Head Drive Pulley Dia. 60 mm High Output Type | Economy Flat Belt Conveyor Built-in Motor Drive Pulley Dia. 70 mm | Economy Double-row Timing Belt Conveyor Head Drive Pulley Dia. 70 mm Built-in Motor | ||
 |  |  | ||
| Representative model: E-CVSE | Representative model: E-CVSMA | Representative model: E-CVGTE |
Related Documents Click here
here