Driver for Motor Driven Roller 35W/50W/80W/120W

Brand :

MISUMI

Caution

Product Description

Dimensional Drawing

Magnetic Encoder Drive Control Card (Number of drives N1)	Magnetic Encoder Drive Control Card (Number of drives N1) 485 Communication	Magnetic Encoder Drive Control Card (Number of drives N4)

Hall Drive Control Card (Number of drives N1)	Hall Drive Control Card (Number of drives N2)

The mounting backplate is made of aluminum alloy, and the main housing material is ABS

Specification Table

■ Place your order after selecting the model and parameters according to selection steps ~ .

Type		DC Supply Voltage	-	Power Drive Configuration	-	Number of Drives	-	Communication Mode
EA-MRD		24	-	C1	-	N1	-	B1

■ Specification table

Type	DC Supply Voltage (V)	Power Drive Configuration	Number of Drives	Communication Mode
EA-MRD	24 48	C1 (35W magnetic encoder) C2 (50W magnetic encoder) C3 (80W magnetic encoder) D1 (35W hall sensor) D2 (50W hall sensor) D3 (80W hall sensor) D4 (120W hall sensor)	N1 (one-to-one)
				A0 (Manual speed adjustment)
				B1 (IO digital PNP)
				B2 (IO digital NPN)
				B3 (IO analog)
				C0 (485 communication)

		D1 (35W hall sensor) D2 (50W hall sensor) D3 (80W hall sensor)	N2 (one-to-two)
				D0 (Profinet)
				F0 (EtherCAT)
		C1 (35W magnetic encoder) C2 (50W magnetic encoder) C3 (80W magnetic encoder)	N4 (one-to-four)	G0 (Ethernet/IP)
				H0 (ModbusTCP)

Communication mode C0 (485 communication) only supports the magnetic encoder drive method.
Drive power configuration D0 (Hall 120W) only supports 48 V DC voltage.
Features of drive control cards with power up to and including 120W:
(1) The magnetic encoder drive control card does not have an integrated drive unit; the drive unit is integrated inside the corresponding magnetic encoder electric roller.V
(2) The Hall drive control card has an integrated drive unit. It is recommended that the cable length between the card and the roller does not exceed 5 meters to avoid affecting signal transmission.

■ Match the electric drum parameter specifications and power supply requirements

DC Rated Voltage (V)	Voltage Range (V)	Rated Power (W)	Rated Current (A)	Starting Current (A)	Switching Power Supply (W)	Recommended Wire Gauge
24	20 to 26	35	2.5±0.5	6.25±0.5	≥ 80	0.75 mm² (4 A)
		50	3.2±0.5	8±0.5	≥ 120	0.75 mm² (4 A)
		80	4.5±0.5	11.25±0.5	≥ 200	1 mm² (6 A)
48	40 to 52	35	1.3±0.5	3.25±0.5	≥ 80	0.75 mm² (4 A)
		50	1.6±0.5	4±0.5	≥ 120	0.75 mm² (4 A)
		80	2.3±0.5	5.75±0.5	≥ 200	1 mm² (6 A)
		120	3.5±0.5	8.7±0.5	≥ 300	1 mm² (6 A)

For actual use with multiple rollers, it is recommended to choose a high-power power supply and avoid using a single power supply whenever possible. For example, when using 35 W motorized rollers,
a 450 W power supply can support 9 to 11 motorized rollers (with staggered roller startup). You can calculate the required power as 1.2 to 1.5 times the total power of the motorized rollers.

■ Application Environment

Operating Ambient Temperature	0℃ to +55℃
Operating Ambient Humidity	10% to 85% RH (no condensation)
Transport and Storage Temperature	-40℃ to +85℃
Vibration	Below 2 G

Example of Use

Application Areas
Used in conjunction with Economy series electric drum motors, available in various models and specifications to enable control of electric drum motors under different operating conditions.

Economy Electric Roller, Straight Roller Surface Type Diameter 50 mm	Economy Electric Roller, Straight Roller Surface Type Diameter 60 mm

EA-MORR-24-50-500-S5-C2-B0-P7-T1-K3	EA-MORR-48-60-450-S7-C2-A0-P7-T1-K3