General-Purpose Hood

Brand :

MISUMI

Caution

Product Description

Harness most commonly used in PLC

● It is a harness that uses the FCN360 connector.
● Wiring is easy thanks to narrow and soft cables with diameter thinness 35% that of conventional cables.
● By taking advantage of the free alteration / custom number, customized connection changes and earth wire length specifications etc. can be performed.
● The combination of the FCN connector and other connectors' harness can be handled with the "Web Design Harness Plus."

Wiring and Wire Color >>Click here
Component Page >>Click here

· The connector clamp parts of harnesses that use F cables (except 40 and 48 core models) are fixed with the sheath peeled and protected with a shrink tubing.
· When the mark tube has no printed custom number specified, the connector pin arrangement number is printed. Be careful not to forget to put the custom number on the supported device.
· Sheath peeling length can be designated as alteration service only for those with terminals or mark tubes.
· The shield holds the lead wire.

Specifications

Compatible Wire

Connector Type	Wire Size
Soldered Type	Loose wire of AWG23 ~ AWG30, or 0.2 mm2 ~ 0.05 mm2
Pressure Welding Type	1.27 mm Pitch Flat Cable AWG28, AWG30 * Loose wires cannot be used. (Fused cables can be used)

Material / Finish

Item	Material / Finish
Insulator	Polyester
Contact	Copper Alloy / Gold Plating

Contact Arrangement Diagram

Electrical Properties

Item	Characteristics	Conditions
Rated Current	3 ADC (1 ADC for pressure welded type) or lower	Allowable current of single contact after coupling
Rated Voltage	250 VAC or less	Allowable voltage within operating temperature range
Contact Resistance	15 mΩ or less	Measured at 6 VDC, 0.3 A
Insulation Resistance	1000 MΩ or more	Between terminals and between ground & terminal are measured at 500 VDC
Withstand Voltage	500 VAC / 1 min	No abnormality to be found when 500 VDC is applied for 1 minute to the same location as the insulation resistance measurement.
Operating Temperature Range	-55°C ~ +85°C	-

Electrical Properties

Item	Characteristics	Conditions
Insertion and Extraction Force Per Single Pole	Insertion Force: 312 g or less, Extraction Force: 50 g or more	When male and female are inserted and extracted, the total extraction force is divided by each core number to convert into force per single pole
Vibration Resistance	No interruption to power supplies of 1 μs or more. Matching contact resistance.	After mounting of compatible electric wires, under conditions of DC current of 100 mA passing through the terminals, it will provide vibrations at a total amplitude of 1.5 mm and vibration frequency of 10 ~ 55 Hz (1 minute reciprocal) in right angled 3 directions for 2 hours.
Insertion and Removal Durability	Contact resistance at 20 mΩ or less. Matching insertion and extraction force per single pole.	Perform insertion-extraction 500 times at a speed of 600 times / hour.

Environmental Properties

Item	Characteristics	Conditions
Temperature Resistance	Matching contact resistance, insulation resistance and withstand voltage.	Performs 5 cycles of -55°C ±0.3 for 30 minutes, 25°C ±10.5 for 10 ~ 15 minutes, 85°C ±0.3 for 30 minutes and 25°C ±10.5 for 10 ~ 15 minutes consecutively.
Humidity Resistance	Matching contact resistance of 100 MΩ or more, insulation resistance and withstand voltage.	Remove after placing in conditions of temperature 40 ±2°C and relative humidity of 90 ~ 95% for 96 hours, remove water droplets and then leave at room humidity conditions for between 1 and 2 hours.
Corrosion Resistance	Contact resistance at 20 mΩ or less.	After testing for 48 hours at saltwater concentration of 5% and temperature of 35°C, wash salt encrustation off with water and let dry.

Connector x Hood Combination Table

Hood Connector			Resin Hood			Zinc Die-cast Hood
			Standard Screw	Long Screw	Hood for Relay	Zinc Die-cast Hood
			FCN-360C0**-B	FCN-360C0**-E	FCN-360C0**-C	FCN-360C040-H-E
Male	Solder Type Connectors	FCN-361P0**-AU	○	○ (8-, 16-core not available)	○ (8-, 16-core not available)	○ (40-core only)
Female	Solder Type Connectors	FCN-361J0**-AU	○	○ (8-, 16-core not available)	○ (8-, 16-core not available)	○ (40-core only)
Female	Pressure Welding Type Connector	FCN-367J0**-AU-F	x	x	x	x

○ = Combination available x = Combination unavailable

・Connectors can be coupled if they have the same core numbers and are a combination of male <--> female.
･ When connecting hood to hood without using a relay hood, use a connecting fixing bracket.