HR10A Connector Straight Harness

Brand :

MISUMI

Caution

Product Description

A best-selling product that can be used in sensors, etc.

● Boasts anti-noise performance by using a double-shielded cable!
● Shield is connected in the shell of the connector.

Wiring and Wire Color Page
>>Click here
Component Page
>>Click here

Specifications

HR10A Connector Straight Harness:Related Image

Specified Length (m)	~ 0.9	1 ~ 4	4.1 ~ 50
Tolerance	+20mm	+50mm	+ 3% of Specified Length

* The tolerance of the specified length is as described above.

Connector Type	Shape Specification Type	Outline Image Drawing (Unit: mm)	Cable Type	Number of Cores	Specified Length (m)


	P (Male Plug)			4	0.2 ~ 50 Can be specified by 0.1 m increments
				6
				10
				12
	S (Female Plug)			4
				6
				10
				12
	PP (Male Plug / Male Plug)			4
				6
				10
				12
	SS (Female Plug / Female Plug)			4
				6
				10
				12
	PS (Male Plug / Female Plug)			4
				6
				10
				12
	PY (Male Plug / Y Terminal) With Pin No. Insertion Mark Tube			4
				6
				10
				12
HR10AP Hirose Electric Co., Ltd	SY (Female Plug / Y Terminal) With Pin No. Insertion Mark Tube			4
				6
				10
				12
	PT (Male Plug / Loose Wires 100 mm) Pin No. Insertion Mark Tube			4
				6
				10
				12
	ST (Female Plug / Loose Wires 100 mm) With Pin No. Insertion Mark Tube			4
				6
				10
				12
	RP (Male Panel Mount)			4
				6
				10
				12
	RS (Female Panel Mount)			4
				6
				10
				12
Connector >>Click here	RPRT (Male Panel Mount / Loose Wires) With Pin No. Insertion Mark Tube			4
				6
				10
				12
	RSRT (Female Panel Mount / Loose Wires) With Pin No. Insertion Mark Tube			4
				6
				10
				12

Connector Type	Shape Specification Type	Outline Image Drawing (Unit: mm)	Cable Type	Number of Cores	Specified Length (m)

	Panel Mount Single Wire Cable Type
HR10AP Hirose Electric Co., Ltd	RPT (Male Panel Mount)			4	0.2 ~ 50 Can be specified by 0.1m increments
				6
				10
				12
Connector >>Click here	RST (Female Panel Mount)			4
				6
				10
				12

Characteristics

Item	Contents
Rated Current	2 A or lower
Rated Voltage	14-core: 150 VAC / 200 VDC, Other: 100 VAC / 140 VDC
Withstand Voltage	300 VAC or less (500 VAC or less for 4-core) / 1 minute
Insulation Resistance	1,000 MΩ or more / 100 VDC
Contact Resistance	10 mΩ or less / 1 ADC
Compatible Wire Size	AWG26 or below Loose Wires or 0.15 mm2 or less Loose Wires

* For applicable wire size, cable finished outer diameter should be within cable clamp inner diameter.

Material / Finish

Item	Materials	Finish
Body Shell	Zinc Alloy	Satin Nickel Plated
Pin Contact	Brass	Silver Plating
Socket Contact	Phosphor Bronze	Silver Plating
Insulator	Polyamide Resin	Black

Contact Arrangement Diagram

Connection Work Method (Relay type can be done by the same method.)

Number of Cores	Wrench Spacing (mm)	D Dimension (mm)	Wrench Tightening Force
4.6	7.5	10	1.5 N・m (15 kgf・cm)
10.12	9.5	16	1.5 N・m (15 kgf・cm)

Connector assembly is performed in the following order.
(1) Pass the cable through the cord bushing and connector body, and then solder to the insulator unit contact.
(2) After soldering the wire to the connector, crimp the clamp brackets attached to the connector with the crimp tool (HR10A-TC-02) or pliers.
(3) Fit the insulator unit screw part into the connector body. (Use a wrench and tighten to the values shown in the table.) When tightening the connector body, loosen the D part first so that the solder connection part is not placed under stress.
(4) Tighten the fastening screw so that its tip touches one of the two bosses on the clamp bracket. Note that the fastening screw is fixed with tightening torque of 0.3 N⋅m (3 kgf⋅cm).
(5) Finally, cover the the cord bushing with the connector body.

Connector Insertion and Removal Method