Slim Press-fit Connector, Angle Model
Brand :
MISUMI
Caution
Product Description
Popular low-priced angle harness!
Angle shape allows easy routing even in a narrow space.
Connection change and specific length of ground wire are available by selecting complementary alteration options and custom No.
● Angle shape is used for easy maneuvering in narrow areas.
· Removal of CN1 is on the B-row side (Wide fitting side).
· When the mark tube has no printed custom number specified, the connector pin arrangement number is printed. Be careful not to forget to put the custom number on the supported device.
· Sheath peeling length can be designated as alteration service only for those with terminals or mark tubes.
· The exposed core parts of the thin cables have been fused together for protection.
Wiring and Wire Color Page >>Click here.
Component Page >>Click here.
Specifications
| Specified Length (m) | ~ 0.9 | 1 ~ 4 | 4.1 ~ 50 |
| Tolerance | +20mm | +50mm | + 3% of Specified Length |
Compatible Wire
| Connector Type | Wire Size |
|---|---|
| Soldered Type | Loose wire of AWG23 ~ AWG30, or 0.2 mm2 ~ 0.05 mm2 |
| Pressure Welding Type | 1.27 mm Pitch Flat Cable AWG28, AWG30 * Loose wires cannot be used. (Fused cables can be used) |
Material / Finish
| Item | Material / Finish |
|---|---|
| Insulator | Polyester |
| Contact | Copper Alloy / Gold Plating |
Contact Arrangement Diagram
Electrical Properties
| Item | Characteristics | Conditions |
|---|---|---|
| Rated Current | 3 ADC (1 ADC for pressure welded type) or lower | Allowable current of single contact after coupling |
| Rated Voltage | 250 VAC or less | Allowable voltage within operating temperature range |
| Contact Resistance | 15 mΩ or less | Measured at 6 VDC, 0.3 A |
| Insulation Resistance | 1000 MΩ or more | Between terminals and between ground & terminal are measured at 500 VDC |
| Withstand Voltage | 500 VAC / 1 min | No abnormality to be found when 500 VDC is applied for 1 minute to the same location as the insulation resistance measurement. |
| Operating Temperature Range | -55°C ~ +85°C | - |
Electrical Properties
| Item | Characteristics | Conditions |
|---|---|---|
| Insertion and Extraction Force Per Single Pole | Insertion Force: 312 g or less, Extraction Force: 50 g or more | When male and female are inserted and extracted, the total extraction force is divided by each core number to convert into force per single pole |
| Vibration Resistance | No interruption to power supplies of 1 μs or more. Matching contact resistance. | After mounting of compatible electric wires, under conditions of DC current of 100 mA passing through the terminals, it will provide vibrations at a total amplitude of 1.5 mm and vibration frequency of 10 ~ 55 Hz (1 minute reciprocal) in right angled 3 directions for 2 hours. |
| Insertion and Removal Durability | Contact resistance at 20 mΩ or less. Matching insertion and extraction force per single pole. | Perform insertion-extraction 500 times at a speed of 600 times / hour. |
Environmental Properties
| Item | Characteristics | Conditions |
|---|---|---|
| Temperature Resistance | Matching contact resistance, insulation resistance and withstand voltage. | Performs 5 cycles of -55°C ±0.3 for 30 minutes, 25°C ±10.5 for 10 ~ 15 minutes, 85°C ±0.3 for 30 minutes and 25°C ±10.5 for 10 ~ 15 minutes consecutively. |
| Humidity Resistance | Matching contact resistance of 100 MΩ or more, insulation resistance and withstand voltage. | Remove after placing in conditions of temperature 40 ±2°C and relative humidity of 90 ~ 95% for 96 hours, remove water droplets and then leave at room humidity conditions for between 1 and 2 hours. |
| Corrosion Resistance | Contact resistance at 20 mΩ or less. | After testing for 48 hours at saltwater concentration of 5% and temperature of 35°C, wash salt encrustation off with water and let dry. |
Connector x Hood Combination Table
| Hood Connector | Resin Hood | Zinc Die-cast Hood | ||||
|---|---|---|---|---|---|---|
| Standard Screw | Long Screw | Hood for Relay | ||||
| FCN-360C0**-B | FCN-360C0**-E | FCN-360C0**-C | FCN-360C040-H-E | |||
| Male | Solder Type Connectors | FCN-361P0**-AU | ○ | ○ (8-, 16-core not available) | ○ (8-, 16-core not available) | ○ (40-core only) |
| Female | Solder Type Connectors | FCN-361J0**-AU | ○ | ○ (8-, 16-core not available) | ○ (8-, 16-core not available) | ○ (40-core only) |
| Pressure Welding Type Connector | FCN-367J0**-AU-F | x | x | x | x | |
○ = Combination available x = Combination unavailable
・Connectors can be coupled if they have the same core numbers and are a combination of male <--> female. ･ When connecting hood to hood without using a relay hood, use a connecting fixing bracket.