for Clean Environment, Tube Fitting PP Type Elbow
Brand :
PISCO
Caution
Product Description
PP resin is used for the main body material, making it ideal for clean environments.
Specifications Of PP Type Tube Fitting For Clean Environments - Elbow
Appearance of PP Type Tube Fitting For Clean Environments - Elbow
Dimensional drawing
| Usable Fluids | Air, water (see condition *1), other (see condition *1) |
|---|---|
| Maximum Operating Pressure | 1.0 MPa (at 0 to 20°C)*2 |
| Operating Vacuum Pressure | -100 kPa |
| Operating Temperature Range | 0 to 80°C (no freezing) |
*1. When the specified fluid is water or other chemicals, the following conditions must be observed.
- 1. When using water or other liquids, make sure the surge pressure stays below the maximum operating pressure.
- 2. Be sure to use an insert ring when using water or other liquids.
- 3. For chemicals, mixed gases, etc., compliance with the specifications may vary depending on usage conditions, so please check before using.
*2. For the maximum operating pressure when the operating temperature exceeds 20°C, see "Relationship between operating temperature and maximum operating pressure" below.
Relationship between operating temperature and maximum operating pressure
- Maximum operating pressure (MPa)
- Operating temperature (°C)
Formats
| Format | Tube Outer Diameter φD | R | A | B | L | φP | Tube End C | E | Hex H | Mass (g) | Effective Cross-Sectional Area (mm2) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PPL4-01 (5) (6) (7) | 4 | R1/8 | 8 | 23.3 | 24.3 | 10 | 15 | 18.1 | 10 | 4 | 3.4 |
| PPL4-02 (5) (6) (7) | R1/4 | 11 | 26.3 | 25.3 | 14 | 4.5 | |||||
| PPL6-01 (5) (6) (7) | 6 | R1/8 | 8 | 25 | 27.3 | 12.5 | 16.9 | 19.9 | 12 | 5 | 8.7 |
| PPL6-02 (5) (6) (7) | R1/4 | 11 | 28 | 28.2 | 14 | 5.5 | |||||
| PPL6-03 (5) (6) (7) | R3/8 | 12 | 29.8 | 29.7 | 17 | 6.5 | |||||
| PPL8-01 (5) (6) (7) | 8 | R1/8 | 8 | 28 | 31.3 | 14.5 | 18.1 | 22.7 | 14 | 7 | 17.2 |
| PPL8-02 (5) (6) (7) | R1/4 | 11 | 31 | 32.2 | 7.5 | ||||||
| PPL8-03 (5) (6) (7) | R3/8 | 12 | 32.8 | 33.7 | 17 | 8.5 | |||||
| PPL10-02 (5) (6) (7) | 10 | R1/4 | 11 | 36 | 38.7 | 17.5 | 20.4 | 26.4 | 17 | 12 | 25.9 |
| PPL10-03 (5) (6) (7) | R3/8 | 12 | 37 | 39.4 | 13 | ||||||
| PPL12-03 (5) (6) (7) | 12 | R3/8 | 12 | 39 | 43.2 | 21 | 23.6 | 29.6 | 22 | 18 | 37.6 |
| PPL12-04 (5) (6) (7) | R1/2 | 15 | 42 | 44.3 | 19 |
Units: mm
- *L dimensions are reference dimensions after tightening with screws.
- *For (5) in the order format, input -F (FMK) or -HN (HNBR) only if you want to change the sealing rubber material. (If you want the clean washing specification, you cannot change the material to FKM.)
- *For (6) in the order format, input -TP if you want the sealing tape specification.
- *For (7) in the order format, input -C if you want the clean room packaging specification or -UC if you want the clean washing specification.