Tube Fitting PP Type Bulkhead Union P for Clean Environments
Brand :
PISCO
Caution
Product Description
[Features]
· The main body uses PP resin suitable for clean environments.
· EPDM is utilized in the seal.
· FKM and NBR types are available as optional extras.
· PP or SUS304 can be selected for the screw element.
· Use of oil permitted.
· Plastic body is clear colored to allow water flow to be observed.
· Two packaging specifications--normal packaging and clean room packaging--are available according to the desired application.
Specifications Of PP Type Tube Fitting For Clean Environments - Bulkhead Union P
Appearance of PP Type Tube Fitting For Clean Environment - Bulkhead Union P
Dimensional drawing
| Usable Fluids | Air, water (see condition *1), other (see condition *1) |
|---|---|
| Maximum Operating Pressure | 1.0 MPa (at 0 to 20°C)*2 |
| Operating Vacuum Pressure | -100 kPa |
| Operating Temperature Range | 0 to 80°C (no freezing) |
- *1. When the fluid used is water or other chemicals, the following conditions must be observed.
- 1. When using water or other liquids, make sure the surge pressure stays below the maximum operating pressure.
- 2. Be sure to use an insert ring when using water or other liquids.
- 3. For chemicals, mixed gases, etc., compliance with the specifications may vary depending on usage conditions, so please check before using.
- *2 For the maximum operating pressure when the operating temperature exceeds 20°C, see "Relationship between operating temperature and maximum operating pressure" below.
Relationship between operating temperature and maximum operating pressure
- Maximum operating pressure (MPa)
- Operating temperature (°C)
Formats
| Format | Tube Outer Diameter φd | M | B | E | A | φP | Tube End C | Hex H | G | Mass (g) | Effective Cross-Sectional Area (mm2) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PPMP4 (5) (7) | 4 | M12 × 1.5 | 31.6 | 9.3 | 12 | 10 | 15 | 14 | 5 | 7.2 | 4.2 |
| PPMP6 (5) (7) | 6 | M14 × 1.5 | 35.8 | 9.9 | 15 | 12.3 | 17.1 | 17 | 5 | 11 | 10.7 |
| PPMP8 (5) (7) | 8 | M16 × 1.5 | 38.4 | 10.7 | 15.5 | 14.2 | 18.1 | 19 | 6 | 15 | 19.1 |
| PPMP10 (5) (7) | 10 | M20 × 2 | 43.4 | 13.2 | 18.5 | 17.5 | 20.9 | 24 | 6 | 25 | 39.6 |
| PPMP12 (5) (7) | 12 | M24 × 2 | 48.8 | 13.4 | 20.5 | 21 | 23.6 | 27 | 6 | 31 | 47.6 |
| PPMP1/4 (5) (7) | 1/4 | M14 × 1.5 | 35.8 | 9.9 | 15 | 12.3 | 17.1 | 17 | 5 | 10 | 10.7 |
| PPMP3/8 (5) (7) | 3/8 | M20 × 2 | 43.4 | 13.2 | 18.5 | 17.5 | 20.9 | 24 | 6 | 25 | 39.6 |
| PPMP1/2 (5) (7) | 1/2 | M24 × 2 | 49.4 | 13.7 | 20.5 | 21 | 23.9 | 27 | 6 | 29 | 47.6 |
Unit: mm
- *For (5) in the order format, input -F (FMK) or -HN (HNBR) only if you want to change the sealing rubber material. (If you want the clean washing specification, you cannot change the material to FKM.)
- *For (7) in the order format, input -C if you want the clean room packaging specification or -UC if you want the clean washing specification.