For General Piping, Tube Fitting, Branch A
Brand :
PISCO
Caution
Product Description
A wide variety of quick-connect fittings for general piping.
[Features]
·Quick-connect fitting for general pneumatic piping.
·After installation, you can change the take-off angle of the resin body. (applicable to some products)
·A wide lineup of products.
·Enables centralized piping
Drawing
Product Specifications
| Operating fluid | Air, water (see conditions*) |
|---|---|
| Maximum operating pressure | 1.0 MPa |
| Operating vacuum pressure | -100 kPa |
| Operating temperature range | 0°C to +60°C (no freezing) |
* When using this product with water, be sure to observe the following conditions.
1. When using this product with water, ensure that the surge pressure will not exceed the maximum operating pressure.
2. This product can be used with general tap water.
3. When using this product with water, ensure to use an insert ring.
1. When using this product with water, ensure that the surge pressure will not exceed the maximum operating pressure.
2. This product can be used with general tap water.
3. When using this product with water, ensure to use an insert ring.
Standard table
Units: mm
| Part number | Tube outer diameter ⌀D | R | A | B | L1 | L2 | ⌀P1 | ⌀P2 | Tube End C |
|---|---|---|---|---|---|---|---|---|---|
| PA4-M5 | 4 | M5 × 0.8 | 3 [3.2] | 17.2 | 14.2 [14] | 6.2 [6] | 10 | 9.8 | 14.9 |
| PA6-01 | 6 | R1/8 | 8 | 27 | 23 | 12 | 12.4 | 15.4 | 17 |
| PA6-01W | 6 | R1/8 | 8 | 27 | 23 | 12 | 12.4 | 15.4 | 17 |
| PA8-02 | 8 | R1/4 | 11 | 31.5 | 25.5 | 13.5 | 14.4 | 19 | 18.2 |
| PA10-03 | 10 | R3/8 | 12 | 36 | 29.7 | 15.7 | 17.6 | 23 | 20.7 |
| PA10-03W | 10 | R3/8 | 12 | 36 | 29.7 | 15.7 | 17.6 | 23 | 20.7 |
| PA12-04 | 12 | R1/2 | 13 | 40.2 | 32 | 16.5 | 21 | 27 | 23.4 |
| PA12-04W | 12 | R1/2 | 13 | 40.2 | 32 | 16.5 | 21 | 27 | 23.4 |
| Part number | J | E | ød | F | T | Width across flats H | Orifice diameter (ømm) | Weight (g) |
|---|---|---|---|---|---|---|---|---|
| PA4-M5 | 10 | 20.2 | — | — | — | 8 | 1.8 | 9.6 |
| PA6-01 | 12 | 26.2 | 3.2 | 10.7 | 14 | 14 | 4.2 | 25 |
| PA6-01W | 12 | 26.2 | 3.2 | 10.7 | 14 | 14 | 4.2 | 25 |
| PA8-02 | 14 | 29.4 | 3.2 | 12.5 | 15 | 17 | 6 | 42 |
| PA10-03 | 17 | 33.5 | 4.2 | 15 | 18 | 21 | 8 | 70 |
| PA10-03W | 17 | 33.5 | 4.2 | 15 | 18 | 21 | 8 | 70 |
| PA12-04 | 20 | 37.4 | 4.2 | 17 | 21 | 24 | 10 | 106 |
| PA12-04W | 20 | 37.4 | 4.2 | 17 | 21 | 24 | 10 | 106 |
*1. W at the end of the part number represents light gray.
*2. The L1 and L2 dimensions of tapered thread type are a reference dimensions after screw tightening.
*3. The values in square parentheses [] are the values for cleanroom packaging specifications and clean washing specifications.
*4. Orifice diameter is obtained by converting the diameter of the minimum flow path.
Usage examples
How To Attach And Detach The Connecting Part
1. How to attach/detach the tube
(1) Installation of tube
By simply inserting a tube until the tube stop, the tube fitting (quick-connect fitting) fixes it with its lock claws, and the elastic sleeve seals the outer circumference of the tube.
By simply inserting a tube until the tube stop, the tube fitting (quick-connect fitting) fixes it with its lock claws, and the elastic sleeve seals the outer circumference of the tube.
(2) Removing a tube
When removing a tube, the lock claws open by pushing collet, and the tube can be pulled out.
Please be sure to turn off the air before removing.
When removing a tube, the lock claws open by pushing collet, and the tube can be pulled out.
Please be sure to turn off the air before removing.
2. Screw tightening method
(1). Screw tightening
There are 2 types of screw tightening: one that tightens by engaging a wench or impact wrench on the outer sides of the hexagonal part, and one that tightens by inserting a hex key inside the hexagonal part (the space between fittings can be shortened).
There are 2 types of screw tightening: one that tightens by engaging a wench or impact wrench on the outer sides of the hexagonal part, and one that tightens by inserting a hex key inside the hexagonal part (the space between fittings can be shortened).
