Corrosion-Resistant SUS304 Fitting, Straight
Brand :
PISCO
Caution
Product Description
If strength is required, optimal for chemical atmospheres.
Corrosion-Resistant Tube Fitting Stainless SUS304 - Straight Specifications
Corrosion-resistant Tube Fitting Stainless SUS304 - Straight appearance
Corrosion-resistant Tube Fitting Stainless SUS304 - Straight dimensional drawing
Corrosion-resistant Tube Fitting Stainless SUS304 - Straight dimensional drawing
(metric thread type)
Usable fluids: air, water (see conditions*), other (see conditions*)
Maximum operating pressure: 1.0 MPa
Operating vacuum pressure: -100 kPa
Operating temperature range: 0 to 60°C (no freezing)
Warning
- *When the fluid used is water or other liquids, the following conditions must be observed.
- When using water or other liquids, make sure the surge pressure stays below the maximum operating pressure.
- Be sure to use an insert ring when using water or other liquids.
- For chemicals, mixed gases, etc., compliance with the specifications may vary depending on usage conditions, so please check before using.
Size Chart
| Format | Tube Outer Diameter øD | R | A | B | L | Tube End C | Hex H | Orifice Diameter (ømm) | Mass (g) |
|---|---|---|---|---|---|---|---|---|---|
| PC4-M5SUS | 4 | M5 × 0.8 | 3 | 20.1 | 17.1 | 15 | 10 | 1.8 | 5.9 |
| PC4-M6SUS | M6 × 1 | 4 | 21.1 | 3 | 6.2 | ||||
| PC4-01SUS | R1/8 | 8 | 7.8 | ||||||
| PC4-02SUS | R1/4 | 11 | 15.1 | 14 | 15 | ||||
| PC6-M5SUS | 6 | M5 × 0.8 | 3 | 22.2 | 19.2 | 17.1 | 12 | 1.8 | 8.5 |
| PC6-M6SUS | M6 × 1 | 4 | 23.2 | 3 | 8.8 | ||||
| PC6-01SUS | R1/8 | 8 | 22.7 | 18.7 | 4.6 | 8.7 | |||
| PC6-02SUS | R1/4 | 11 | 24.7 | 14 | 17 | ||||
| PC6-03SUS | R3/8 | 12 | 23.7 | 17.4 | 17 | 26 | |||
| PC8-01SUS | 8 | R1/8 | 8 | 27.9 | 23.9 | 18.2 | 14 | 6 | 15 |
| PC8-02SUS | R1/4 | 11 | 26.6 | 20.6 | 7 | ||||
| PC8-03SUS | R3/8 | 12 | 23.9 | 17.6 | 17 | 22 | |||
| PC10-01SUS | 10 | R1/8 | 8 | 30.5 | 26.5 | 20.9 | 17 | 6 | 22 |
| PC10-02SUS | R1/4 | 11 | 30 | 24 | 8.5 | 20 | |||
| PC10-03SUS | R3/8 | 12 | 29.5 | 23.2 | 25 | ||||
| PC10-04SUS | R1/2 | 15 | 30.5 | 22.3 | 21 | 47 | |||
| PC12-02SUS | 12 | R1/4 | 11 | 36.1 | 30.1 | 23.5 | 21 | 8.5 | 41 |
| PC12-03SUS | R3/8 | 12 | 32.1 | 25.8 | 11 | 34 | |||
| PC12-04SUS | R1/2 | 15 | 34.1 | 25.9 | 47 | ||||
| PC16-03SUS | 16 | R3/8 | 12 | 39.5 | 33.2 | 25 | 24 | 11 | 56 |
| PC16-04SUS | R1/2 | 15 | 41.5 | 33.3 | 13 | 63 |
Units: mm
- *Taper thread type L dimensions are reference dimensions after tightening with screws.
Applicable Tube Size
Millimeter size: ø4 (diameter 4 mm), ø6 (diameter 6 mm), ø8 (diameter 8 mm), ø10 (diameter 10 mm), ø12 (diameter 12 mm), ø16 (diameter 16 mm)
Applicable Tube Size
| Metric Thread | M5 × 0.8, M6 × 1 |
|---|---|
| Taper Pipe Thread | R1/8, R1/4, R3/8, R1/2 |
- *See the manufacturer's catalog for other precautions and important notes.