Polycarbonate Plate -Transparent -High Strength & Heat Resistant
Caution
Product Description
Achieves superior impact strength and glass transparency. Note: Quoted from the 2013 Takiron comprehensive catalog.
[Features]
· Polycarbonate plates are made from materials with superior impact resistance, even among plastics.
· Plastic with a transparency equal to glass that refutes the common belief that transparent materials are easy to break.
· Possesses the highest level of impact-resistance strength while using transparent materials with approximately 20 times the strength of hard vinyl chloride and approximately 40 times the strength of acrylic.
· Superior light permeability rate of 85% for 5 mm transparent plate, the same transparency as high grade plate glass.
· Low thermal conductivity (1/5th of glass) and superior heat retention qualities. Useful for insulation.
· Can be used in a wide range of temperatures, from -40°C to +120°C.
· 1 mm thickness and resistant to high voltages of up to 30,000 volts. More than twice the insulating value as Bakelite. Optimal as electric insulation material.
· Weather-resistant grade that prevents yellowing and is barely affected by direct sunlight, wind, rain, temperatures, etc., when compared to other plastic materials. Quality can be selected based on application.
[Polycarbonate Processing Features]
1. Little change in load (creep) and easy drilling and cutting.
2. Vacuum forming and heat bending possible.
3. Cold forming by bending into a curve under temperatures below room temperature is possible.
· Food and Hygiene Law / UL certified product / Railway car compliance certified product.
Product Specifications
| Item evaluated | Unit | PC1600 | ||
|---|---|---|---|---|
| Physical Properties | Specific Gravity | — | 1.20 | |
| Rockwell Hardness | M scale | 67 | ||
| R scale | 125 | |||
| Mechanical Properties | Tensile yield stress | MPa | 63 | |
| Nominal strain at break | % | 90 | ||
| Tensile elasticity | MPa | 2250 | ||
| Notched Charpy impact strength | kJ/m^2 | 13.0 | ||
| Tensile impact strength | kJ/m^2 | 220 | ||
| Bending stress | MPa | 91 | ||
| Bending Elasticity Ratio | MPa | 2300 | ||
| Compressive yield stress | MPa | 78 | ||
| Compressive Modulus | MPa | 1900 | ||
| Shear fracture stress | MPa | 65 | ||
| Thermal Properties | Deflection Temp. Under Load | °C | 0.45 MPa | — |
| °C | 1.80 MPa | 139 | ||
| Vicat Softening Temperature | °C | Method A (10 N) | — | |
| °C | Method B (50 N) | 150 | ||
| Heat distortion rate | % | Vertical | ※3 3.5 | |
| lateral | ※3 -0.2 | |||
| Linear expansion coefficient | × 10-5·K-1 | 6.5 | ||
| Thermal conductivity | W/m·K | 0.19 | ||
| Specific Heat | J/g·K | 1.30 | ||
| Flame Resistance | — | — | ||
| Electrical Properties | Surface Resistivity | ohms per square | 10^15 or more | |
| Volume resistivity | Ω・m | 10^13 or more | ||
| Dielectric strength | MV/m | 20 | ||
| Permittivity (1 MHz) | — | 3 | ||
| Dielectric loss tangent (1 MHz) | — | 0.009 | ||
| — | Laminating properties | — | — | |
| Moisture Absorption | % | 0.240 | ||
| Optical Properties | Total light transmission | % | 89 | |
| Haze | — | — | ||
| Hue | — | Transparent | ||
* The indicated values are actual measured values for a test piece with a thickness of 5 mm, and are not guaranteed values.
Test condition 190°C / 60 minutes (tested according to JIS K 6735)
Specifications table
Performance / test information
Light Transmittance by Wavelength
