5-Port Solenoid Valve, Plug-In Cassette Type, SQ2000 Series Valve

Brand :

SMC

Caution

Product images may be representative. Refer to the manufacturer's catalog for details.

Product Description

SMC Solenoid Valve.
[Features]
· Clip type one-touch fittings for easy replacement of fittings
· The connector entry direction can be changed with a single push
· 4 position, dual 3-port valve
· Built-in back pressure check valve

Plug-In Unit SQ2000 Series Specifications

Plug-in unit SQ2000 Series external appearance

The single-action fittings can be replaced without removing the valve

The connector entry direction can be changed with a single push

Valve Specifications	Valve Construction		Metal Seal	Rubber Seal
	Fluid		Air
	Maximum Operating Pressure		0.7 MPa
	Minimum Operating Pressure	Single	0.1 MPa	0.15 MPa
		Double (double solenoid)	0.1 MPa	0.1 MPa
		3 position	0.1 MPa	0.2 MPa
		4 Position Type	-	0.15 MPa
	Ambient Temperature and Operating Fluid Temperature		-10 to 50°C ^*1
	Lubrication		Not required
	Pilot Valve – Manual Operation		Push type (tool required), locking type (tool required), sliding-lock type (manually operated)
	Vibration-Resistance / Impact-Resistance ^*2		30/150 m/s²
	Enclosure		Dust-proof
Solenoid Specifications	Coil Rated Voltage		12, 24 V DC
	Allowable Voltage Fluctuation		±10% of rated voltage
	Coil Insulation Type		Class B or equivalent
	Power Consumption (Current)	24 V DC	DC 0.4 W (17 mA), DC 0.95 W (40 mA) ^*3
	Power Consumption (Current)	12 V DC	DC 0.4 W (34 mA), DC 0.95 W (80 mA) ^*3

*1: Use dry air when operating at low temperatures. No condensation.
*2: Vibration resistance: No malfunctions occurred in a 1-sweep test between 45 and 2,000 Hz. The test was performed in both energized and non-energized states and in the axial direction and at right angles to the main valve and armature. (Initial value)
Impact resistance: No malfunctions after testing using a drop-type impact tester under the following conditions: in the axial direction and at a right angle to the main valve and armature in both energized and non-energized states (once for each condition state).
*3: Values for high-speed response type.

Model

Series	Switching Method		Sealing Method	Model	Flow Rate Characteristics ^*1						Response Time [ms] ^*2		Weight (g)
					1 → 4/2 (P → A/B)			4/2 → 5/3 (A/B → R1/R2)			Standard (0.4 W)	High Speed Response (0.95 W)
					C (dm³/ [s·bar])	b	Cv	C (dm³/ [s·bar])	b	Cv	Standard (0.4 W)	High Speed Response (0.95 W)
SQ2000	2 Position	Single	Metal Seal	SQ2130	2.2	0.17	0.51	2.4	0.14	0.57	35 or less	20 or less	145
		Single	Rubber Seal	SQ2131	2.3	0.17	0.51	3.1	0.18	0.71	31 or less	24 or less	140
		Double	Metal Seal	SQ2230D	2.2	0.17	0.51	2.4	0.14	0.57	20 or less	15 or less	160
		Double	Rubber Seal	SQ2231D	2.3	0.17	0.51	3.1	0.18	0.71	26 or less	20 or less	155
	3 Position	Closed Center	Metal Seal	SQ2330	1.9	0.17	0.46	2.1	0.15	0.47	56 or less	37 or less	180
		Closed Center	Rubber Seal	SQ2331	1.9	0.17	0.46	1.8	0.29	0.47	44 or less	34 or less	175
		Exhaust Center	Metal Seal	SQ2430	1.9	0.17	0.46	2.4	0.14	0.55	56 or less	37 or less	180
		Exhaust Center	Rubber Seal	SQ2431	1.9	0.17	0.46	3.1	0.14	0.65	44 or less	34 or less	175
		Pressure Center	Metal Seal	SQ2530	2.3	0.17	0.51	2.1	0.18	0.47	56 or less	37 or less	180
		Pressure Center	Rubber Seal	SQ2531	2.5	0.17	0.56	1.8	0.30	0.47	44 or less	34 or less	175
	4 Position	Dual 3-Port Valve	Rubber Seal	SQ2A31 SQ2B31 SQ2C31	1.5	0.17	0.40	1.5	0.17	0.40	34 or less	19 or less	155

*1: Values for the top ported cylinder connection port diameter C8, CYL. → EXH. The side ported type is approximately 10% smaller.
*2: Based on JIS B 8419:2010. (Value at supply pressure of 0.5 MPa and with light and surge voltage suppressor. The values may change depending on the pressure and air quality.)

Product JIS Symbol

JIS symbol for 2 position single

JIS symbol for 3 position closed center

JIS symbol for 4 position dual 3 port valve (B)

With/Without Manifold Block

Without manifold block external appearance

When ordering together with manifolds
When only valve is required

With manifold (built-in back pressure check valve) external appearance

When adding stations

*Lead wire not included.

Cylinder Port Connection Port Diameter

Side ported external appearance

Top ported external appearance

*Can be changed to side ported.

ø4‑mm (pipe connection port diameter) single-action fitting
ø6 (pipe connection port diameter 6 mm) single-action fitting
ø8 (pipe connection port diameter 8 mm) single-action fitting

Precautions

*When energizing valves for a long period of time, heat generated by the coil will cause the temperature to rise, decreasing valve performance, decreasing the lifespan and adversely affecting nearby peripheral equipment.
*When energizing a valve continuously, be sure to use the standard type (0.4 W) at an ambient temperature of 40°C or less and pay attention to discharging heat.
*Temperature increases are particularly high when simultaneously energizing 3 or more neighboring stations for a long-period continuously or when simultaneously energizing the A side and B side of a dual 3-port valve for an extended period.
Be sure to read the individual product cautions before use.
See the SMC catalog for product information other than that detailed above.