DeviceNet Compliant Connector, HR31 Series
Caution
Product Description
These are DeviceNet standard compliant connectors. These connectors simplify connection, reduce plug connector size, and promote differentiation compared to conventional parts.
[Features]
· DeviceNet compliant: The HR31 series is a FA network device standards product. (Terminal contacts: Gold-plated)
· Screw-lock: All screw-lock equipped products can be securely locked, allowing for increased locking strength.
· Snap-lock: The snap-lock feature creates a tactile click when mating.
· Commercially available tools can be used: These connectors are designed to be used with crimp tools conforming to JIS C 9711 standards.
· Designed to allow for removal by ⌀1 mm pin when improperly wired.
· Protected contacts: The crimped contacts are protected by the plug housing, reducing damage to the contacts during connection.
DeviceNet Compliant Interface Connector With Miniaturized Plug Connector For Simplified Terminations
Compliant with FA network devices
Total space occupied by mated assemblies
Includes screw lock
Main Features of HR31 Series DeviceNet Compliant Connector
HR31
Products made by other manufacturers
| Item | Products made by other manufacturers | HR31 |
|---|---|---|
| Reduced number of termination operations | Crimp the wire to a commercially-available cap connector and insert it into the housing and fasten with the screw. (*) | Crimp and connect onto the contact, and then fasten by simply inserting into the housing. |
| Supports high-density mounting | Plug height is 15 mm. | Because the plug height has a low-profile at just 10.2 mm, it supports higher density mounting on connector mounting surfaces. |
| Prevention of connection errors | Contact positions not identified | Permanently identified contact positions. |
| Reducing the number of required operations to secure receptacle assembly to the board | Connectors are secured from the underside of the board using screws. | No need for screws; features built-in locking pins which secure the connector to the board. |
- *Although it is possible to terminate discrete cables with screws and not use a pin contact, there are potential issues and concerns for long-term reliability. Therefore, most manufacturers recommend to use crimp contacts.
Product Specifications
Product Standards
| Rating | Rated Current | 12 A (when using 2.5 mm2wire) 10 A (when using a 1.5 mm2 wire) | Operating Temperature Range | -40°C to +100°C |
|---|---|---|---|---|
| Rated voltage | 250 V AC, 350 V DC | Storage temperature range | -40°C to +85°C |
| Item | Standard | Conditions |
|---|---|---|
| 1. Contact resistance | 5 mΩ or less | Measure at 1 A DC |
| 2. Insulation resistance: | 1,000 MΩ or more | Measure at 500 V DC |
| 3. Withstand voltage | There shall be no flashover or dielectric breakdown | 2,000 V AC for 1 min. |
| 4. Impulse withstand voltage | There shall be no flashover or dielectric breakdown | 4‑KV standard waveform, positive and negative, 3 times each |
| 5. Vibration resistance | There shall be no electrical discontinuity for 10 μs or greater | 10 Hz to 55 Hz to 10 Hz: 5 mins. Single amplitude 0.75 mm, Three directions, 10 cycles each |
| 6. Mating cycle | Contact resistance: 10 mΩ or less | 1,000 times |
| 7. Temperature cycle | Insulation resistance: 1,000 MΩ or more | -40°C: 30 mins. > Room temperature: 10 to 15 mins. > +100°C: 30 mins. > Room temperature: 10 to 15 mins for 5 cycles |
| 8. Humidity resistance | Insulation resistance: 10 MΩ or more (at high humidity) 100 MΩ or more (when dry) | Temperature: 40°C, Humidity: 90 to 95%, 96 hours |
Materials
| Item | Materials | Finish | Note | |
|---|---|---|---|---|
| Plug | Insulator | PBT resin | Black/green | UL94V-0 |
| Screw | Steel | Nickel plating | ||
| Crimp contact | Female contacts | Contact area: phosphor bronze, Termination area: copper | Contact area: gold plating, Termination area: tin plating | |
| Receptacle | Insulator | PBT resin | Black/green | UL94V-0 |
| Male contact | Brass | Gold plating | ||
| Nut | Steel | Nickel plating | ||
| Pin | Phosphor bronze | Tin plating | Board retention pin | |
Product Usage Precautions
1. To prevent damage, align the receptacle with the panel and board in such a way that it is not subject to excess loads.
1.1 Dimensions of recommended mounting panel (right-angle DIP)
| Product No. | A | |
|---|---|---|
| HR31-5.08R-5PDL(**) | 36 | +0.2 0 |
1.2 Dimensions of recommended mounting panel (straight DIP)
| Product No. | B | |
|---|---|---|
| HR31-5.08R-5PD(**) | 36 | +0.2 0 |
2. Insert the crimp contact into the plug in the direction shown below.
Crimp contact / wire
3. Use a number 0 cross drive bit to tighten the screw lock's screw.
4. Make sure the power is off before mating or un-mating the connector.